Hw-module Slot
2021年1月17日Register here: http://gg.gg/nvs0d
*Cisco Hw-module Slot
*Hw-module Slot 1 Oversubscription
*Hw-module Slot R1 Stop
*Hw-module Subslot
Hw Module Slot 1 Oversubscription, unethical poker, brevard poker, 55 pratt street casino High Limit This game is a High Limit title and has a higher minimum spend per spin than the other slot games. For example, $100 free but you must wager it 100 times in total, then you can only withdraw if Hw Module Slot X Oversubscription Port Group Y your balance is above $200, and the maximum payout is $200. There are many Rival software casinos in particular that offer chips like these which we are a waste of time. Solved: Hi everybody, can anybody help me with this: Please explain to me what do this comand:’hw-module module 7 reset ’ I used this comand, and it cause me this problem: PEP76VAL02#hw-module module 7 reset Proceed with reset of standby. Hw Module Slot R1 Reload, quick hits slots apk, online casinos uk players, betsafe poker where is the hand history located.Can anyone comment on RSP redundancy with SSO mode?
I have a test 7507 with rsp-k4pv-mz.120-32.S8.bin on both RSP2s. I’ve done
this:
service single-slot-reload-enable
redundancy
no keepalive-enable
mode sso
And it doesn’t seem to ever sync the slave
ranttest#show red
Redundant System Information :
------------------------------
Available system uptime = 14 minutes, 49 seconds
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = none
Hardware Mode = Duplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = hsa
Maintenance Mode = Disabled
Communications = Down Reason: Simplex mode
Current Processor Information :
-------------------------------
Active Location = slot 2
Current Software state = ACTIVE
Uptime in current state = 13 minutes, 24 seconds
Image Version = Cisco Internetwork Operating System
Software
Cisco Hw-module SlotIOS (tm) RSP Software (RSP-K4PV-M), Version 12.0(32)S8, RELEASE SOFTWARE
(fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Mon 20-Aug-07 16:34 by leccese
BOOT =
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
Peer (slot: 3) information is not available because it is in ’DISABLED’
state
ranttest#redundancy force-switchover
Cannot perform switchover until the standby is fully initialized.
The box is up, its got two OSPF adjacencies, maybe a hundred routes - its
not doing anything fancy, so I’m kind of stuck here. The production target
Hw-module Slot 1 Oversubscriptionis 7507s /w RSP4s, the same OSPF, and about 180k routes via BGP. Any idea
what might be wrong here?
_______________________________________________
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nspHw-module Slot R1 Stop
Hw-module Subslotarchive at http://puck.nether.net/pipermail/cisco-nsp/
Register here: http://gg.gg/nvs0d
https://diarynote-jp.indered.space
*Cisco Hw-module Slot
*Hw-module Slot 1 Oversubscription
*Hw-module Slot R1 Stop
*Hw-module Subslot
Hw Module Slot 1 Oversubscription, unethical poker, brevard poker, 55 pratt street casino High Limit This game is a High Limit title and has a higher minimum spend per spin than the other slot games. For example, $100 free but you must wager it 100 times in total, then you can only withdraw if Hw Module Slot X Oversubscription Port Group Y your balance is above $200, and the maximum payout is $200. There are many Rival software casinos in particular that offer chips like these which we are a waste of time. Solved: Hi everybody, can anybody help me with this: Please explain to me what do this comand:’hw-module module 7 reset ’ I used this comand, and it cause me this problem: PEP76VAL02#hw-module module 7 reset Proceed with reset of standby. Hw Module Slot R1 Reload, quick hits slots apk, online casinos uk players, betsafe poker where is the hand history located.Can anyone comment on RSP redundancy with SSO mode?
I have a test 7507 with rsp-k4pv-mz.120-32.S8.bin on both RSP2s. I’ve done
this:
service single-slot-reload-enable
redundancy
no keepalive-enable
mode sso
And it doesn’t seem to ever sync the slave
ranttest#show red
Redundant System Information :
------------------------------
Available system uptime = 14 minutes, 49 seconds
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = none
Hardware Mode = Duplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = hsa
Maintenance Mode = Disabled
Communications = Down Reason: Simplex mode
Current Processor Information :
-------------------------------
Active Location = slot 2
Current Software state = ACTIVE
Uptime in current state = 13 minutes, 24 seconds
Image Version = Cisco Internetwork Operating System
Software
Cisco Hw-module SlotIOS (tm) RSP Software (RSP-K4PV-M), Version 12.0(32)S8, RELEASE SOFTWARE
(fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Mon 20-Aug-07 16:34 by leccese
BOOT =
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
Peer (slot: 3) information is not available because it is in ’DISABLED’
state
ranttest#redundancy force-switchover
Cannot perform switchover until the standby is fully initialized.
The box is up, its got two OSPF adjacencies, maybe a hundred routes - its
not doing anything fancy, so I’m kind of stuck here. The production target
Hw-module Slot 1 Oversubscriptionis 7507s /w RSP4s, the same OSPF, and about 180k routes via BGP. Any idea
what might be wrong here?
_______________________________________________
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nspHw-module Slot R1 Stop
Hw-module Subslotarchive at http://puck.nether.net/pipermail/cisco-nsp/
Register here: http://gg.gg/nvs0d
https://diarynote-jp.indered.space
コメント